Intake manifold · MK3 1993–1999 · MK4 1999.5–2006

MK3 vs. MK4 8-Valve Intake Manifold

Stock vs. Stage 3 ported, on the flow bench and the dyno

13.5 → 9worst-runner restriction (in. H₂O)
+23 whpPorted MK4 vs. OEM at 2,500 rpm
112.3peak whp, ported MK4

Proven dyno results are the only way to show that an upgrade works, and the results are often surprising. This test compared the MK3 (1993–1999) and MK4 (1999.5–2006) 8-valve intake manifolds, each stock and fully ported.

Test car (unchanged throughout)

Car
VW Corrado, naturally aspirated ABA 2.0 swap
Block
1995 OBD1 ABA, stock bore/rods/pistons, fresh rings and bearings, windage tray
Head
German casting, milled .025", street port, 3-angle valve job, TT dual springs, TT272 hydraulic cam
Compression
10.29 : 1 (cc'd)
ECU
MS2 v3.57, extra firmware 2.10
Ignition
GM wasted-spark coil packs, MS-controlled
Injectors
Ford Motorsport 24 lb/hr
Exhaust
AMK stainless 4-2-1 header, 2.25" pipe
Throttle body
Stock OBD1

Flow bench

Upper and lower sections were tested together, one runner at a time, with all vacuum ports plugged and air pushed in through the throttle-body opening. Restriction is measured in inches of water, so lower is better.

MK4 manifold restriction per runnerLOWER IS BETTER

  • Runner 1: stock13.5 in. H₂O
  • Runner 1: ported9 in. H₂O
  • Runner 2: stock10 in. H₂O
  • Runner 2: ported9 in. H₂O
  • Runner 3: stock10 in. H₂O
  • Runner 3: ported9 in. H₂O
  • Runner 4: stock10.25 in. H₂O
  • Runner 4: ported9 in. H₂O
Stock runner #1 is far more restrictive than the others. After porting, all four runners read the same 9".

Dyno

Wheel horsepower by manifold

4050607080901001101202,5003,0003,5004,0004,5005,0005,5006,0006,500Engine speed (rpm)whpOEM MK4: 47 @ 2,500 rpmOEM MK4: 64 @ 3,000 rpmOEM MK4: 67 @ 3,200 rpmOEM MK4: 74 @ 3,500 rpmOEM MK4: 86 @ 4,000 rpmOEM MK4: 102 @ 4,500 rpmOEM MK4: 108 @ 5,000 rpmOEM MK4: 108 @ 5,500 rpmOEM MK4: 102 @ 6,000 rpmOEM MK4: 92 @ 6,500 rpmPorted MK3: 74 @ 3,500 rpmPorted MK3: 83 @ 4,000 rpmPorted MK3: 97 @ 4,500 rpmPorted MK3: 104 @ 5,000 rpmPorted MK3: 106 @ 5,500 rpmPorted MK3: 101 @ 6,000 rpmPorted MK3: 82 @ 6,500 rpmOEM MK3: 67 @ 3,200 rpmOEM MK3: 73 @ 3,500 rpmOEM MK3: 81 @ 4,000 rpmOEM MK3: 97 @ 4,500 rpmOEM MK3: 107 @ 5,000 rpmOEM MK3: 108 @ 5,500 rpmOEM MK3: 101 @ 6,000 rpmOEM MK3: 87 @ 6,500 rpmPorted MK4: 70 @ 2,500 rpmPorted MK4: 76 @ 3,000 rpmPorted MK4: 80 @ 3,200 rpmPorted MK4: 85 @ 3,500 rpmPorted MK4: 95 @ 4,000 rpmPorted MK4: 101 @ 4,500 rpmPorted MK4: 110 @ 5,000 rpmPorted MK4: 111 @ 5,500 rpmPorted MK4: 107 @ 6,000 rpmPorted MK4: 100 @ 6,300 rpm
  • Ported MK4
  • OEM MK4
  • Ported MK3
  • OEM MK3
View data table
RPMPorted MK4OEM MK4Ported MK3OEM MK3
2,5007047––
3,0007664––
3,2008067–67
3,50085747473
4,00095868381
4,5001011029797
5,000110108104107
5,500111108106108
6,000107102101101
6,300100–––
6,500–928287
Peak results
ManifoldPeak whpPeak wtq (lb·ft)
OEM MK3107.58114.03
Ported MK3107.18113.62
OEM MK4110.85119.76
Ported MK4112.29119.62

Findings. Porting the MK3 manifold made no measurable gain on this engine. The MK4 manifold beats the MK3 even in stock form. Ported, it adds a small amount of peak power and a large gain below 4,000 rpm, more than 20 whp at 2,500 rpm, where a street car spends most of its time.

Questions about this research?

Porting services are no longer offered, but the data stays here for reference. Ask us about the results or about our intake kits.

Get in touch